USB Capture AIO fra Magewell er en 12-bits lyd- og videoopptak / avspillingsenhet som støtter USB 3.0, og lar deg ta opp 12-bits HDMI eller analog lyd. I tillegg støtter det RGB & YCbCr (YUV) fargestørrelser, støtter tilpasset EDID, og har integrert kabelutjevning som støtter kabellengder på opptil 754 'for HD-SDI-signaler.

USB 3.0-vertsgrensesnittet er direkte kompatibelt med ulike redigeringsprogrammer som VLC, VirtualDub, OBS, XSplit, vMix, VidBlaster, Wirecast, Microsoft Media Encoder og Adobe Flash Media Encoder. Den er kompatibel med Windows og Linux-systemer.

• SDI + embedded audio + analog audio
• HDMI + embedded audio + analog audio
• DVI + audio
• VGA + audio
• Component + audio
• Composite + audio
• S-video + audio

Input

• Auto scan of video input sources when there is no signal input to the currently selected input source
• Manual selection of video input source
• Auto selection of linked (embedded) audio input source when the video input source changes
• Manual selection of audio input source
• Support for input video resolutions up to 2048 x 2160

VGA & Component

• 12-bit ADC
• Support for RGB & YCbCr (YUV) color formats
• Support for Separated sync, Composite sync, SOG (Sync-on-Green), SOY (Sync-on-Luminance)
• Support for DMT, CEA, CVT, GTF video timings
• Input signals up to 165MHz pixel rate are digitized with 1:1 sampling
• Auto detection of RGB & YCbCr color formats
• Auto or manual sampling phase adjustment
• Auto horizontal alignment
• Support for customized video timings
• Support for customized video resolutions for CVT/GTF timings

HDMI

• 225MHz HDM receiver
• Adaptive HDMI equalizer support for cables lengths up to 98’ (30m)
• Support for customized EDID
• Support for extraction of AVI/Audio/SPD/MS/VS/ACP/ISRC1/ISRC2/Gamut Info Frames
• Full colorimetric support
• Support for 8/10/12-bit color depths
• Support for RGB 4:4:4, YCbCr 4:4:4, YCbCr 4:2:2 color sampling
• Support for up to 2-channel IEC60958 audio streams
• Support for extraction of audio formation information & channel status data
• Support for extraction of video timing information
• Support for extraction of 3D format information
• Support for Side-by-Side Half, Top-and-Bottom, Frame Packing 3D mode

SDI

• Integrated cable equalizer supporting cable lengths up to 754’ (230m) for HD-SDI signals
• Support for SD/HD/3Ga/3Gb/3Ga-DL/3Gb-DS standards
• Support for 2K (2048 x 1080) mode
• Support for RGB 4:4:4, YCbCr 4:4:4, YCbCr 4:2:2 color sampling
• Support for 10/12-bit color depth
• Support for extraction of SMPTE 352 payload identifier
• Support for up to 8 (mono) audio channels at 48 kHz
• Support for extraction of audio formation information & channel status data
• Limited support of 3Gb-DS: only the first stream can be captured
• Limited support for capture of the first link of dual link interfaces: YCbCr 4:2:2 10-bit 1080p 50/59.94/60: captured as 1080i 50/59.94/60, YCbCr 4:4:4 10-bit: captured as 4:2:2, RGB 4:4:4: R/B sub-sampled

YC & Composite

• 12-bit ADC
• Support for NTSC, PAL, and SECAM standards
• Auto detection of video input standard

Analog Audio

• Capture analog audio via 3.5mm unbalanced Line In interface

Video Processing

• Video processing pipelines with 160 Mp/s processing bandwidth
• Video cropping
• Video scaling
• Video De-Interlacing: Weave, blend top & bottom field, top field only, bottom field only
• Video Aspect Ratio Conversion: Auto or manual selection of input aspect ratio, auto or manual selection of capture aspect ratio, three aspect ratio conversion modes - Ignore (Anamorphic), cropping, or padding (Letterbox or Pillarbox)
• Video Color Format Conversion: Auto or manual selection of input color format & quantization range, Auto or manual selection of capture color format, quantization range & saturation range, support for RGB, YCbCr 601, YCbCr 709 color formats, support for limited or full quantization range, support for limited, full & extended gamut saturation range
• Video frame rate conversion
• Vertical flip and mirror

Multiple Devices on One Computer

• Support for connecting multiple USB devices to one system
• Support for setting the device serial number as the device name shown in the system using USB Capture Utility

SDK

• USB Capture SDK provide functions including signal status extraction, capture configuration, etc.